File: MXTES.FC of Tape: Various/ETH/fc2

(.FC,.FO Focal format converted to 'WRITE' listing) 

---

C-MTESLA.FC     77

01.02 I (LG)LG,1.03,LG
01.03 D 31;G 2.01
01.04 C                             STRICT=0       TORQUE=1
01.05 C FAST MESS
01.10 S Z=KI+J*DK*1E-3;S H=1/Z;D 25
01.25 S Z=FIOP(-4095);S Z=FADC(TP)
01.26 F I=1,10;S Z=FELD(ST)
01.27 S !=-1
01.30 S Z=FELD(ST)
01.32 I (!)1.32
01.33 S Z=FELD(R)*10
01.34 I (FITR((H-Z)/PR))1.27,1.38;T %3.1,(H-Z)*1E4;G 1.27
01.38 F ST=0,1;D 3
01.60 S J=J+1;I (J-N)1.1
01.70 S N=J
01.76 F I=0,35;T "-"
01.77 S TV=FSQT(TQ);T " TM= "%5.03,TM,"[K] +/- ",TV
01.78 F J=1,6;S Z=FOUT(MD(J))
01.80 S LG=2.01;S ST=0
01.81 O R O;S Z=FOUT(140)
01.82 O C
01.83 D 30.92
01.84 O I TTY:,E;O O TTY:,E
01.85 Q
01.90 T !!"SET FIELD AT:",%6.04,H,"[T]          "

02.01 C PRIMER
02.10 D 6
02.14 A !,"DK[1E-3/T]       ",DK;I (-FABS(DK))2.18;A "HF[T]         ",HF
02.17 S DK=1E3*(HI-HF)/(HI*HF*N);T !"DK="%4.03,DK,"[1E-3/T]";G 2.25
02.18 S HF=HI/(1+N*DK*1E-3*HI);T "HF=",%6.04,HF,"[T]"
02.25 S H=HI
02.31 S PR=FITR(DK*10*HF*HF)/1E4;T !"SW.SPEED =",%2,PR*1E4/4,"[G/S]";C 4 SEC LOOP
02.32 T  "   V(IND)  <=",%5.02,52*PR/(4*.1472),"[V]"
02.33 S X=(HI-HF)*4/PR;T !"SWEEP TIME",%3,X/60," [MIN]",%2,X-FITR(X/60)*60," [SEC]"
02.34 I (1E-4-PR)2.35;S PR=1E-4
02.35 T ">>> OK?   THEN: GO"!;S LG=2.4;Q
02.40 D 4;D 13.8;L N FOCCOM.ZE;S Z=FX(0,500)
02.41 S TM=0;S TQ=0;S H=HI+.01;D 16;D 1.9
02.42 D 27
02.43 T !"RUN BEGINS, START SWEEP          ";T ""
02.60 G 29.05

03.01 C DVM DOUBLE MEAS
03.30 S Z=FADC(ST);S #=-1
03.35 I (-ST)3.39;D 16;G 3.4
03.39 D 10
03.40 I (#)3.4;S Z=FADC(R);S V=Z/1000;C TP!!
03.41 I (-FABS(V))3.45;T "0"
03.45 S V=V-6
03.47 I (ST-1)3.48;S V=V*(KI*H)
03.48 S X=J+256*(ST-FITR(J/256))
03.50 S Z=FCOM(X,V);D 13.6
03.51 O R O
03.52 T %5.03,FCOM(X),!
03.53 O O TTY:,E
03.60 S Z=FIOP(2^4+2^5);D 7

04.01 CALIBRATE
04.05 S Z=FADC(TT)
04.09 A !"EICHUNG IN 1E-03 PF        ",Y
04.10 T !"UPPER C          ";D 27;S Z=FIOP(-4095);S V=FADC(Q)*1E-4
04.20 T !"LOWER C          ";D 27;S Z=FADC(Q)*1E-4
04.21 T %5.04,V,Z
04.25 S X=8.859*KD^2*PI*1000/(4*PF*PF)
04.30 S ES=Y*X/(Z-V);T !%5.04,ES,"[ANGSTROEM/V]"
04.35 A !"SHUNT NUMBER          ",Y
04.36 S Z=FITR((Y-1)/3);S X=Y-3*Z
04.37 I (X-3)4.38;S X=5
04.38 S Y=X*10^(Z+1)
04.39 T "   R-SHUNT = ",%6,Y," [OHM]";S Y=Y*5.19;C GAIN 2
04.40 A !"COIL NUMBER 1,2       ",Z
04.45 S V=12.63;S X=85;I (1-Z)4.5;S V=37.55;S X=0
04.50 S X=V*FABS(FSIN((HR-X)*PI/180))*HI*1E-4;C CM^2
04.55 S ES(1)=SG*1E7*X/Y;T !,%5.04,ES(1),"[NM/V*10^-7]"

05.01 C FOUR
05.10 A ?SI?,?SF?;S X=(SF-SI)/16;I (X-FITR(X)-.5)5.14;S X=X+.5
05.14 S V=FITR(X)/16;S SF=SI+V*256;S SI=SI+V*128
05.16 T %3,"'"V*32"'"
05.20 D 13.9;D 12
05.30 S Z=FOUR(SI,V);S Z=FX(1,760)

06.01 C PARAMS
06.05 A !!"RUN              ",R
06.10 S MD(5)=176+FITR(R/10);S MD(6)=1936+R-10*MD(5)
06.40 A !"HI[T]            ",HI;S KI=1/HI
06.50 A !"N                ",N,"HR            ",HR
06.55 A !"DILA: PS         ",PS,"PT            ",PT,"PF            ",PF
06.57 A !"TORQ: PS         ",PS(1),"PT            ",PT(1),"PF            ",PF(1)

07.01 C CHECKS
07.10 I (-FABS($-211))7.2;S Z=FIN();D 7.9;S LG=2.4;Q
07.20 S Z=FIOP()-2048;I (-Z)7.3;R
07.30 I (Z-9)7.4;T "M";R
07.40 T "T";D 7.9;S LG=1.1;Q
07.90 T !"BACK UP          "

08.01 C DATA*SQRT(H/HI)
08.10 D 13.8;S KI=1/HI;S Y=FSQT(HI)
08.20 F I=0,N-1;S Z=KI+I*DK*1E-7;S H=1/Z;D 8.3
08.25 R
08.30 S Z=FCOM(I,FCOM(I)*FSQT(H)/Y);D 13.5

10.01 C DISPLAY J
10.10 S Z=J/100;F U=137,139;D 11.2

11.01 C DISPLAY TS
11.10 S Z=FABS(TS);S U=127;D 11.2;S U=129;D 11.2;S U=130
11.15 D 11.2;S U=131
11.20 S X=FITR(Z);S Y=FDIS(U,X-80);S Z=10*(Z-X)+1E-6

12.01 C FOURSCALE
12.10 S X=194;S U=SI/100;S Y=FITR(U)
12.12 I (-Y)12.14;S Z=FDIS(X+2,-96);G 12.16
12.14 S LG=12.2;G 12.52
12.16 D 12.8;I (-Y)12.18;S Z=FDIS(X+1,-96);G 12.8
12.18 D 12.9;G 12.8
12.20 S X=201;S U=SI/100;S Y=FITR(U);S LG=12.3;G 12.5
12.30 S X=212;S U=SF/100;S Y=FITR(U);S LG=12.34;G 12.5
12.34 S LG=2.01;R
12.50 I (-Y)12.52,12.54
12.52 D 12.9;G 12.56
12.54 S Z=FDIS(X,-96);S X=X+1
12.56 D 12.8;D 12.9;D 12.8;D 12.9;G LG
12.80 S U=(U-Y)*10+1E-4;S Y=FITR(U)
12.90 S Z=FDIS(X,Y-80);S X=X+1
12.92 G 12.2

13.01 C DIS SWITCH
13.40 S Z=FDIS(0,0)
13.50 S Z=FX(0,500)
13.60 S Z=FX(ST,500)
13.70 S Z=FDIS(Z,FABS(FDIS(Z)));S Z=FDIS(Y,-FABS(FDIS(Y)))
13.80 S Z=4;S Y=5;D 13.7
13.90 S Z=5;S Y=4;D 13.7

16.01 C DISPLAY H
16.10 S Z=H;F U=146,147;D 11.2
16.20 F U=149,151;D 11.2

18.01 C ALIAS
18.10 S I=0;T "FREQS IN [T] AND DK IN [1E-3/T]"
18.12 S I=I+1;T !"FREQ",%2,I,:10;A A(I);I (A(I))18.12,18.15,18.12
18.15 S U=I-1;T !
18.20 A !"DK",DK;I (-DK)18.25,18.8
18.25 F I=512,567;S Z=FCOM(I,160)
18.30 S V=500/DK
18.50 F I=1,U;S X=A(I);D 19;S X=X*55/V;S Z=FCOM(X+512,FCOM(512+X)+16+I)
18.60 F I=1,4;T :I*14,"'"
18.65 T #,:14;F I=0,55;S Z=FOUT(FCOM(I+512))
18.70 T :50,"'",%4.02,V;G 18.2
18.80 S DK=500/V;T !"     DK IS NOW",%5.03,DK,"*1E-3[T]"!

19.01 C ALIAS SR
19.10 S Z=0
19.20 S X=X-V;I (X)19.4,19.4;S Z=Z+1;G 19.2
19.40 S Z=Z/2;S Z=FITR(Z)-Z
19.50 I (Z)19.6;S X=FITR(V+X);R
19.60 S X=FITR(-X);R

23.01 C LEGENDRE
23.05 S A(1)=0;S A(2)=0;S A(3)=0;S A(4)=0
23.10 F I=0,N-1;D 24
23.15 S A(2)=A(2)*3;S A(3)=A(3)*5;S A(4)=A(4)*7
23.20 T !,%6.04,"A0=",A(1),"A1=",A(2),"A2=",A(3),"A3=",A(4)

24.01 C SUB OF 23
24.10 S U=FCOM(I)/(N-1)
24.20 S Y=I/(N-1)
24.30 I (-FABS(I*(I-N+1)))24.6;S U=U/2
24.60 S A(1)=A(1)+U
24.70 S A(2)=A(2)+(2*Y-1)*U
24.80 S A(3)=A(3)+(6*Y^2-6*Y+1)*U
24.90 S A(4)=A(4)+(20*Y^3-30*Y^2+12*Y-1)*U

25.01 C MEASURE T OXFORD
25.10 S Z=FIOP(3);S Z=FADC(TT);S Z=FADC(ST);S #=-1
25.20 I (#)25.2;S X=FLOG(FADC(R)*10)
25.30 S TS=3.9035E-2-8.4771E-2*X+1.2858E-2*X*X;S TS=1/TS
25.40 S TQ=TQ+(TS-TM)^2*J/(J+1)
25.50 S TM=TM+(TS-TM)/(J+1)
25.60 D 11

26.01 C TEST
26.10 S Z=FIOP(-4095);S Z=FIOP(Y);S Z=FADC(TT)
26.20 S Z=FADC(Q)
26.30 I (-FABS($-199))26.2;S $=2000;S Z=FIN()

27.01 C WAIT
27.05 S X=FIOP();S X=0
27.10 I (10-X) 27.15;S X=X+1;G 27.2
27.15 T "";S X=0
27.20 I (-FABS($-199))27.3;S X=FIN();S $=2000;R
27.30 I (FABS(FIOP())),27.1;R

29.01 C STORE
29.05 S MD(4)=216;C DOUBLE FILE!!
29.20 O O STEUER
29.30 T !"30.4 O O DKA1:";D 1.78
29.35 T !"30.92 O I DKA1:";D 1.78
29.40 T !"G 29.9"
29.50 T !
29.60 O C
29.70 O I STEUER
29.80 Q
29.90 O I TTY:,E

30.01 C FALL THRU
30.30 I (-FABS(MP))30.4;S MP=1
30.40 O O DKA1:WPDX83
30.45 F J=1,6;S Z=FOUT(MD(J))
30.50 T %2,R,!,%4,N,!
30.55 F ST=0,1;D 30.6;D 30.7
30.57 S J=0;O O TTY:,E;G 1.1
30.60 T "20",!,%6.04,,DK,!,HR,!,HI,!,HF,!,PF(ST),!,PS(ST),!,PT(ST),!
30.70 T ST,!,TM,!,TV,!,SH(ST),!,MP,!,ES(ST),!,KL,!,KV,!,%5.03,,0,!,0,!,0,!,0,!,0,!
30.92 O I DKA1:WPDX83

31.01 C INIT
31.02 L P FOUPIC
31.03 E
31.04 S $=2000;S U=0;S V=0;S X=0;S Y=0;S Z=0;S H=0;S PR=0;S I=0
31.05 S DK=0;S TS=0;S TQ=0;S TM=0;S J=0
31.08 T !"W#:        ";S MD(1)=215;S MD(2)=FIN();S MD(3)=FIN();S MD(4)=216
31.10 S TP=1;S TT=1;S LG=2.01
31.12 T !!"-K KL KLA KLAM KLAMM KLAMME KLAMMER!!!!!         ";D 27
31.15 T !"-PAR: 1 & 2 : -TAU >=100MSEC         ";D 27
31.20 T !"-TURN INSTR. AMP.(GAIN 2) ON         ";D 27
31.25 T !"-TURN FIELD MEASURING DEVICE ON      ";D 27
31.30 T !"-INSTR. AMP. OFFSET TEST             ";S Y=2^11;D 26
31.33 T !"-MUX #1=TEMP INPUT TEST              ";S Y=2^0+2^1;D 26
31.35 T !"-MUX #5=DILA INPUT TEST              ";S Y=-4095;D 26
31.40 T !"-MUX #6=TORQ INPUT TEST, COIL INT    ";S Y=2^4+2^5
31.41 T !"   -UPPER C                          ";D 27;D 26.1;D 26.2;S V=Z
31.42 T !"   -LOWER C                          ";D 27;D 26.1;D 26.2
31.43 S SG=FSGN(V-Z)
31.55 T !"-DVM: 'FAST' AND '10 V'              ";D 27
31.62 A !"-KRISTALLLAENGE IN CM                ",KL
31.65 A !"-KRISTALLDURCHMESSER IN CM           ",KD
31.66 A !"-KRISTALLVOLUMEN IN CCM              ",KV
31.70 R

---